Convertitori di Media Hi-PoE S-1110HP-XT
Conversione Media in Fibra e PoE compatibile con IEEE 802.3bt

- Da Rame 10/100/1000 a Fibra 1G
- Connettori SC/ST a fibra doppia o SC a fibra singola
- Fornisce alimentazione PSE Hi-PoE IEEE 802.3bt (fino a 100 W)
- Compatibile con dispositivi PoE IEEE 802.3af e PoE PoE+ IEEE 802.3at
- Porte PoE singole o doppie 10/100/1000Base-T
- Caratteristiche avanzate: Azzeramento PD, ridondanza fibra, Smart Link Pass-Through, notifica guasto fibra, Auto-MDIX e loopback
- Temperatura di esercizio estesa da -40°C a +75°C
I Convertitori di Media in fibra S-1110HP-XT di Perle collegano in modo trasparente il rame alla fibra e forniscono fino a 100 Watt di potenza tramite dispositivi PSE Hi-PoE conformi a IEEE 802.3bt a dispositivi compatibili con le norme. Le apparecchiature che si trovano nei dispositivi di gestione del traffico, nelle tubazioni di trasporto petrolio e gas, di tracciamento meteorologico, in applicazioni industriali e in ambienti esterni devono funzionare a temperature non supportate dai Convertitore di Media disponibili in commercio. Con temperature di esercizio comprese tra -40°C a +75°C, questo Convertitori di Media Hi-PoE è perfetto per l'uso con dispositivi industriali soggetti ad ambienti difficili e temperature estreme, quali videocamere di sorveglianza con funzionalità di panoramica-inclinazione-zoom (pan-tilt-zoom, PTZ) con riscaldatori, punti di accesso wireless 802.11ax/ac, allarmi, dispositivi di controllo traffico, sensori e dispositivi di tracciamento.
I Convertitori di Media Hi-PoE di Perle sono classificati come apparecchi di alimentazione elettrica (Power Sourcing Equipment, PSE). Utilizzando cavi UTP standard che trasmettono i dati Ethernet, i Convertitori di Media Hi-PoE di Perle erogano potenza ai dispositivi alimentati (Powered Device, PD) che supportano la norma IEEE 802.3bt PoE (fino a 100 W di potenza) o soluzioni precedenti allo standard, tra cui UPoE, 4PPoE, PoE++, UltraPoE, PoE a 4 doppini, ecc. Poiché questo standard è completamente compatibile con le versioni precedenti delle norme preesistenti IEEE 802.3af PoE e IEEE 802.3at PoE+, sono supportati anche tutti i relativi PD. Il Convertitore di Media in fibra S-1110HP-XT è dotato di porte RJ45 10/100/1000Base-T singole o doppie che alimentano uno o due PD per ogni convertitore. Ulteriori informazioni su PoE
I Convertitori di Media in fibra S-1110HP-XT sono dotati di porte per fibra fisse che supportano fibra multimodale o monomodale con connettori ST/SC doppi o connettori SC per fibra a fascio singolo.
- aumentano la durata degli apparecchi non su fibra ottica, consentendo la trasmissione dei dati dai dispositivi 10/100/1000Base-T tramite su 1000Base-X
- aumentano la distanza di una rete preesistente, collegando il cablaggio CAT5/6/7 alla fibra multimodale o monomodale fino a 10km
- proteggono i dati Ethernet dal rumore EMI e dalle interferenze, interconnettendo i dispositivi Ethernet in rame tramite fibra.
Gli amministratori di rete possono "vedere tutto" grazie alle funzionalità avanzate di Perle, quali negoziazione automatica, Auto-MDIX, Link Pass-Through, notifica di guasto fibra e loopback. Questo rende possibile una più efficace risoluzione dei problemi e minori interventi di manutenzione in loco. Tali funzioni che consentono di risparmiare tempo e denaro si aggiungono alla garanzia a vita e all'assistenza tecnica gratuita in tutto il mondo, rendendo i Convertitori di Media PoE S-1110HP di Perle la scelta preferita dei professionisti IT.
Funzioni dei Convertitori di Media Hi-PoES-1110HP-XT
Power Over Ethernet ( PSE ) |
Pienamente compatibile con IEEE 802.3bt Type 3 e 4 PSE Esegue la funzione Power Sourcing Equipment (apparecchi di alimentazione elettrica, PSE) su 1 o 2 porte UTP per i dispositivi conformi a IEEE 802.3bt. Tutti i modelli supportano i dispositivi PD di tipo 1 (PoE), tipo 2 (PoE+), tipo 3 (Hi-PoE) e tipo 4 (Hi-PoE) |
Gestione dell'alimentazione avanzata |
|
Riavvio PD |
Ideale per il riavvio in remoto delle apparecchiature, questa funzionalità configurabile consente di eseguire un momentaneo ripristino dell'alimentazione del Powered Device (PD) collegato. Se abilitata, il Convertitore di Media provvederà, in caso di perdita del segnale RX in fibra, a disattivare l'alimentazione PSE in uscita fornita al dispositivo PD per 2 secondi, quindi a riattivarla e lasciarla attiva fino alla successiva perdita di un collegamento RX in fibra (dopo il precedente ripristino). Se disabilitata, la perdita di un link RX in fibra non avrà alcun effetto sull'alimentazione PSE fornita ai PD. |
Supporto PD (Powered Device) |
PD Digitare: 1, 2, 3 e 4 PD Classe: 1, 2, 3, 4, 5, 6, 7, 8 Supporta connessioni PD a firma singola e doppia |
Configurazioni multiporta |
|
Fascetta pressacavi | Tutti i modelli sono provvisti di una fascetta pressacavi che garantisce una connessione sicura al convertitore di media. Ideale per ambienti soggetti a vibrazioni. |
Auto-Negotiation (802.3u) |
Il Convertitore di Media supporta la negoziazione automatica. L'interfaccia in fibra 1000Base-X effettua la negoziazione secondo lo standard 802.3 37. L'interfaccia 10/100/1000Base-T effettua la negoziazione secondo lo standard 802.3 28 e 40. L'interfaccia 1000Base-X si collegherà al suo corrispondente una volta raggiunto l'HCD (Highest Common Denominator) ed effettuata la connessione dell'interfaccia in rame con il suo corrispondente. L'interfaccia 1000Base-X continuerà a ripetere la negoziazione trasmettendo una segnalazione di dispositivo remoto offline (purché questa sia abilitata mediante l'impostazione dello switch) fino a quando la rete in rame non si collega e gli HCD non corrispondono. Il Convertitore di Media supporta l'auto-negotiation nelle seguenti condizioni: full duplex, half duplex, guasto remoto, pausa full duplex, pausa asimmetrica e Auto-MDIX. |
Auto-MDIX |
Quando è abilitata, la funzione Auto-MDIX (Automatic Medium-Dependant Interface Crossover) rileva i segnali sull'interfaccia Ethernet in rame per determinare il tipo di cavo collegato (incrociato o passante diretto) e configura automaticamente la connessione. Il Convertitore di Media è inoltre in grado di effettuare correzioni per compensare gli errori di disposizione dei fili in una coppia. Il Convertitore di Media è in grado di compensare fino a un massimo di 120 ns di delay skew (differenza di ritardo) tra le coppie 1000Base-T. |
Smart Link Pass-Through | Quando lo switch Link Mode viene messo in modalità Smart Link Pass-Through, la porta Ethernet in rame rispecchia lo stato della porta 1000Base-X del Convertitore di Media. Questa funzione si può utilizzare indipendentemente dal fatto che la funzione Auto-Negotiation sull'interfaccia in fibra sia abilitata o disabilitata. |
Fiber Fault Alert | Con la funzione Fiber Fault Alert, lo stato del ricevitore 1000Base-X viene passato al trasmettitore 1000Base-X. In questo modo vengono segnalati eventuali guasti al dispositivo corrispondente collegato all'interfaccia 1000Base-X del Convertitore di Media. Se il trasmettitore 1000Base-X è inattivo a causa del guasto, verrà riattivato periodicamente per consentire la risoluzione di questa condizione nel caso in cui il dispositivo corrispondente sull'interfaccia 1000Base-X utilizzi una tecnica analoga. Questo elimina il rischio di lock-out che si verifica con alcuni Convertitore di Media. La procedura è valida solo quando la funzione Auto-Negotiation sull'interfaccia in fibra è disabilitata. |
Pause (IEEE 802.3xy) |
La segnalazione delle pause è una funzione IEEE che sospende temporaneamente la trasmissione di dati tra due dispositivi nel caso in cui uno dei due sia sovraccarico. Il Convertitore di Media supporta la negoziazione Pause sulla connessine 10/100/1000Base-T e la connessione in fibra 1000Base-X.
|
Duplex | È supportato il funzionamento in full e half duplex. |
Pacchetti jumbo | Trasparente per pacchetti jumbo fino a 10 KB. |
VLAN | Trasparente per i pacchetti con tag VLAN. |
Loopback remoto | In grado di eseguire un loopback sull'interfaccia in fibra 1000Base-X. |
Non è quello che stai cercando? Visualizza tutti i Convertitore di Media in Fibra Perle.
Hai bisogno di aiuto? Contatta Perle.
Hardware Specifications
Power | |
---|---|
Input Supply Voltage | 52 - 57 vDC |
Power Consumption | 1 x 10/100/1000Base-T port models: 4 watts 2 x 10/100/1000Base-T port models: 4.7 watts Note: for the HP PoE SFP models the numbers above don’t include the SFP power consumptions |
Power Over Ethernet (PSE) | up to 100 watts per port |
Power Connector | 2-Pin pluggable terminal block |
Indicators | |
Power (PWR) | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when either fiber port is in Loopback test mode. The LED will blink quickly if there is a hardware failure where the reason code can be identified through a combination of FDF,LKF, FDC and PSE indicator LEDs |
Fiber link on / Receive activity (LKF 1/2) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared. |
Copper link on / Receive activity (LKC 1/2) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the 10/100/1000 UTP port If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared. |
Fiber Duplex (FDF 1/2) |
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-X link is operational in full duplex mode. The LED is off when in half duplex. If the Auto-Neg switch is turned off, this LED will always be on |
Copper Duplex (FDC 1/2) |
This green LED is operational only when power is applied. The LED is on when the 10/100/1000Base-T link is operational in full duplex mode. The LED is off when in half duplex |
100/1000 | This multi-color LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 1000 Mbps. The LED is yellow when the speed of the copper Ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps. |
PSE Status (PSE 1/2) | This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE; GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :
OFF — PSE function switch disabled RED — Blinking: Error Conditions
|
Switches - accessible through a side opening in the chassis | |
![]() |
|
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex, half duplex, pause and remote fault capabilities.
Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
Link Mode | Link Mode provides a transparency to the state of the copper link allowing for simplified trouble shooting from the devices connected to the media converter. Normal (Default — Up) With Fiber Auto Negotiation disabled the state of the copper link has no effect on the 1000Base-X link. Smart Link Pass Through (Down) With Fiber Auto-Negotiation disabled the behavior is as follows. When the copper receiver is off the 1000Base-X transmitter will be turned off. When the 1000Base-X receiver goes off the copper transmitter will be turned off. |
Fiber Fault Alert | The Fiber Fault Alert switch has meaning when Auto-Negotiation is disabled Enabled (Default - Up) Disabled (Down) |
Loopback | The media converter can perform a loopback on the 1000Base-X fiber interface. Disabled (Default - Up) Enabled - The 1000Base-X receiver is looped to the 1000Base-X transmitter. The copper transmitter is taken off the interface. |
Speed Copper | 100 (Default) 10 |
Duplex Copper | Full (Default) Half |
Fiber Negotiation | Up: The Media Converter will negotiate Ethernet parameters on the fiber connection. This will ensure that the most optimal connection parameters will be in effect. If connecting to another Perle Media Converter, this parameter should be set to Auto. The Media Converter Module will advertise 1000Mbps, Full and Half Duplex, no Pause. Down: The Media Converter Module’s fiber will be fixed to 1000Mbps, Full Duplex. |
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
PSE Power | Settable for each UTP port available. When enabled (UP), the media converter will perform a Power Sourcing Equipment (PSE) function as per IEEE802.3bt standard. Default is "enabled" |
PD Power Reset | This is a technique to perform a power reset on a PD device(s) attached. When enabled (down), the media converter will upon loss of link on any fiber port, turn off PSE output power to the PD device(s) for 2 seconds then turn the power back on. The power remains on until any fiber link transitions from up to down again. With Passthrough enabled (Link Mode enabled and Fiber Auto-Negotiation enabled) , a loss of link on the fiber resulting from a loss of link on the copper, a PD Power Reset till still occur. When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device(s). |
PoE power vs Ethernet CAT | CAT3 and above for PoE power up to 15.4 watts CAT5 and above for PoE power between 15.4 watts and up to 30 watts CAT6 and above for PoE power between 30 watts and up to 100 watts Note: always choose the highest Ethernet CAT category between desired speed and PoE power |
Connectors | |
10/100/1000Base-T | RJ45 connector 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. 4 pair CAT5 UTP cable for Gigabit. Note: always choose the highest Ethernet CAT category between desired speed and PoE power |
Magnetic Isolation | 1.5kv |
Fixed Fiber | Dual multimode or single mode (Duplex) fiber - SC, ST Single strand fiber (Simplex) - SC |
Filtering | |
Filtering | 1024 MAC Addresses |
Frame Specifications | |
Buffer | 1000 Kbits frame buffer memory |
Size | Maximum frame size of 10,240 bytes -- Gigabit Maximum frame size of 2048 bytes -- Fast Ethernet |
Environmental Specifications | |
Operating Temperature | -40 C to 75 C (-40 F to 167 F) |
Storage Temperature | -40 C to 85 C (-40 F to 185 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output (BTU/HR) |
1 x 10/100/1000Base-T port models: 13.65 BTU/hr 2 x 10/100/1000Base-T port models: 16 BTU/hr |
MTBF (Hours)* | 342019 |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.4 Kg, 1.0 lbs (no power adaptor) |
Dimensions | 150 x 95 x 26 mm, 5.9 x 3.7 x 1.0 inches |
Packaging | |
Shipping Weight | 0.56 kg, 1.2 lbs |
Shipping Dimensions | 300 x 200 x 70 mm, 11.81 x 7.87 x 2.75 inches |
Regulatory Approvals | |
Emissions | FCC Part 15 Class A, EN55022 Class A |
CISPR 22 Class A CISPR 32:2012/EN 55032:2012 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | UL/EN/IEC 62368-1 (previously 60950-1) CAN/CSA C22.2 No. 62368-1 |
CE | |
Laser Safety | EN 60825-1 Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A991 |
HTSUS Number: 8517.62.0020 | |
Perle Limited Lifetime Warranty |
*Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Gigabit Fiber per telecamere IP |
---|
Connetti 10/100/1000 telecamere IP a backbone Gigabit La fibra viene eseguita da un armadio dati esistente a un'area con accesso alla rete. Hi-PoE Media Converter può essere alimentato da 57 VDC o standard da 100 a 240 AC. Il media converter è collegato all'alimentatore e al cavo in fibra. Il cavo di rame (cavo UTP o STP) può essere esteso di altri 100 metri alla telecamera IP. Hi-PoE Media Converter converte i dati da fibra a rame, aggiungendo potenza e trasmettendoli alla telecamera di sicurezza. Per semplificare il cablaggio, i Convertitori di Media PoE multiporta consentono il concatenamento, con una porta uplink in fibra e una porta di downlink in fibra, della fibra tra i convertitori di supporti (noto anche come architettura bus). ![]()
![]() |
Gigabit Fiber ai punti di accesso wireless |
Connetti 10/100/1000 punti di accesso wireless a backbone Gigabit La fibra viene eseguita da un armadio dati esistente a un'area con accesso alla rete. Hi-PoE Media Converter può essere alimentato da 57 VDC o standard da 100 a 240 CA. Il media converter è collegato all'alimentatore e al cavo in fibra. Il cavo di rame (cavo UTP o STP) può essere esteso di altri 100 metri al punto di accesso wireless. Hi-PoE Media Converter converte i dati da fibra a rame, aggiungendo energia e trasmettendoli al WAP. Per semplificare il cablaggio, i Convertitori di Media PoE multiporta consentono il concatenamento, con una porta uplink in fibra e una porta di downlink in fibra, della fibra tra i convertitori di supporti (noto anche come architettura bus). ![]()
![]() |
Fibra Gigabit ai telefoni desktop/VoIP (Voice over IP) |
Connetti 10/100/1000 workstation e telefoni VoIP a un backbone Gigabit La fibra viene eseguita da un armadio dati esistente a un'area con accesso alla rete. Hi-PoE Media Converter può essere alimentato da 57 VDC o standard da 100 a 240 CA. Il media converter è collegato all'alimentatore e al cavo in fibra. Il cavo di rame (cavo UTP o STP) può essere esteso per altri 100 metri al telefono IP. Hi-PoE Media Converter converte i dati da fibra a rame, aggiungendo energia e trasmettendoli al telefono IP. ![]() ![]() |
Uplink a Doppia Fibra Ridondante |
Connettività Uplink in fibra garantita per le tue attrezzature critiche 1. Redundant Fiber : Fibra ridondante quando il collegamento primario non riesce, il Convertitore di Media reindirizza il traffico verso l'altra porta in fibra entro 50 ms.
![]() 2. Redundant Primary : Primario ridondante quando il collegamento primario non riesce, il Convertitore di Media reindirizza il traffico verso la porta in fibra secondaria entro 50 ms. Al ripristino del collegamento in fibra primaria, il traffico viene automaticamente reindirizzato alla fibra primaria.
![]() ![]() |
Modalità singola/fibra singola |
Collegare le porte in rame su un singolo filamento di fibra (denominato anche BiDi "bidirezionale") ![]()
Tuttavia, per ridurre i costi o laddove vi sono limiti sulla fibra disponibile, è possibile utilizzare la tecnologia WDM. WDM utilizza frequenze di trasmissione e ricezione separate per comunicare su un singolo filo di fibra. La tecnologia WDM si basa sul fatto che le fibre ottiche possono trasportare simultaneamente molte lunghezze d'onda della luce senza interazione tra ciascuna lunghezza d'onda. Pertanto, una singola fibra può trasportare simultaneamente molti segnali o canali separati di lunghezze d'onda. Quindi ricordate, se viene utilizzata la fibra Single Strand, avrete bisogno di un “Up” Convertitore di Media su un lato e a “Down” Media Converter sull'altro per la conversione da rame a fibra. |
Select a Model to obtain a Part Number - S-1110HP-XT Hi-PoE
Model |
# PoE ports |
Fiber Port Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Core Size (um) |
Modal Bandwidth (MHz*Km) |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Min | Max | Min | Max | ||||||||||
S-1110HP-SC05-XT | 1 | Dual SC |
1000Base-SX |
-9.5 |
-4.0 |
-17 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
|||||||||||
50 |
400 |
500 m
(1,640 ft) |
|||||||||||
50 |
500 |
550 m
(1,804 ft) |
|||||||||||
50 |
2000 |
1000 m
(3281 ft) |
|||||||||||
S-1110HP-ST05-XT | 1 | Dual ST |
1000Base-SX |
-9.5 |
-4.0 |
-17 |
-3.0 |
7.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
|||||||||||
50 |
400 |
500 m
(1,640 ft) |
|||||||||||
50 |
500 |
550 m
(1,804 ft) |
|||||||||||
50 |
2000 |
1000 m
(3281 ft) |
|||||||||||
S-1110HP-SC10-XT | 1 | Dual SC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
1000 m
(3281 ft) |
50 |
400 |
550 m
(1,804 ft) |
|||||||||||
50 |
400 |
550 m
(1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
||||||||||
S-1110HP-ST10-XT | 1 | Dual ST |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m
(1,804 ft) |
50 |
400 |
550 m
(1,804 ft) |
|||||||||||
50 |
400 |
550 m
(1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
||||||||||
S-1110DHP-SC05-XT | 2 | Single SC |
1000Base-SX |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
|||||||||||
50 |
400 |
500 m
(1,640 ft) |
|||||||||||
50 |
500 |
550 m
(1,804 ft) |
|||||||||||
50 |
2000 |
1000 m
(3281 ft) |
|||||||||||
S-1110DHP-ST05-XT | 2 | Single ST |
1000Base-SX |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
850 |
MMF |
62.5 |
160 |
220 m
(722 ft) |
62.5 |
200 |
275 m
(902 ft) |
|||||||||||
50 |
400 |
500 m
(1,640 ft) |
|||||||||||
50 |
500 |
550 m
(1,804 ft) |
|||||||||||
50 |
2000 |
1000 m
(3281 ft) |
|||||||||||
S-1110DHP-SC10-XT | 2 | Single SC |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m
(1,804 ft) |
50 |
400 |
500 m
(1,640 ft) |
|||||||||||
50 |
500 |
550 m
(1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
||||||||||
S-1110DHP-ST10-XT | 2 | Single ST |
1000Base-LX/LH |
-9.5 |
-3.0 |
-20 |
-3.0 |
10.5 |
1310 |
MMF* |
62.5 |
500 |
550 m
(1,804 ft) |
50 |
400 |
500 m
(1,640 ft) |
|||||||||||
50 |
500 |
550 m
(1,804 ft) |
|||||||||||
SMF |
** |
- |
10 km
(6.2 mi) |
Single Fiber Models Recommended use in pairs
Model | # PoE ports |
Connector | Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Core Size (um) |
Modal Bandwidth (MHz* Km) |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|---|---|---|
Min | Max | Min | Max | ||||||||||
S-1110HP-SC10U-XT | 1 |
Single SC |
1000Base-BX-U |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1310 / 1490 |
SMF |
** |
- |
10 km
(6.2 mi) |
S-1110HP-SC10D-XT | 1 |
Single SC |
1000Base-BX-D |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1490 / 1310 |
SMF |
** |
- |
10 km
(6.2 mi) |
S-1110DHP-SC10U-XT | 2 |
Single SC |
1000Base-BX-U |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1310 / 1490 |
SMF |
** |
- |
10 km
(6.2 mi) |
S-1110DHP-SC10D-XT | 2 |
Single SC |
1000Base-BX-D |
-9.0 |
-3.0 |
-20 |
-3.0 |
11 |
1490 / 1310 |
SMF |
** |
- |
10 km
(6.2 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*A mode-conditioning adapter as specified by the IEEE standard, is required regardless of the span length. Note how the mode conditioning adapter for 62.5-um fibers has a different specification from the mode-conditioning adapter for 50-um fibers.
**ITU-T G.652 SMF as specified by the IEEE 802.3z standard.
Media Converter Accessories | |
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |