Convertitori di Media per Temperatura Industriale S-110-XT
Conversione da 10/100Base-TX a 100Base-X

- Convertitore di Media per fibra da 10/100Base-TX a 100Base-X
- Estensione delle distanze di rete fino a 20km per apparecchiature Ethernet industriali
- Funzioni avanzate - Link Pass-Through, Far-End Fault, Auto-MDIX e Loopback
- Temperatura di funzionamento tra -40°C e +75°C (-40°F to +165°F)
- Connettore di alimentazione per scatola terminale
I Convertitori di Media di Temperatura Industriale S-110P-XT soddisfano l'esigenza di collegare in maniera trasparente al cavo in fibra ottica dispositivi Ethernet 10/100 funzionanti in temperature estreme. I Convertitori di Media S-110P-XT funzionano in temperature industriali comprese tra -40°C e +75°C. L'apparecchiatura utilizzata nella gestione del traffico, negli oleodotti e gasdotti, nel meteo tracking, nelle applicazioni industriali e da esterni funziona in temperature che i Convertitori di Media commerciali non sono in grado di tollerare. Grazie a questa funzione per la temperatura estesa e ad un rivestimento in acciaio resistente, il Convertitore di Media S-110P-XT rappresenta un mezzo economico per estendere la distanza tra due dispositivi industriali soggetti ad ambienti rigidi e temperature forti quali telecamere di sicurezza, punti di accesso wireless, sensori e impianti di localizzazione.
Gli amministratori di rete sono in grado di "vedere tutto" grazie a funzioni avanzate quali Auto-Negotiation, Auto-MDIX, Link Pass-Through, Far End Fault e Loopback remoto. Questo garantisce una maggiore efficienza nella soluzione dei problemi e minore manutenzione in loco. Queste caratteristiche di risparmio di costi e tempo, insieme con una garanzia a vita e un supporto tecnico gratuito a livello mondiale, fanno dei Convertitori di Media 10/100 di Temperature Industriali S-110-XT Perle una scelta intelligente per i professionisti dell'informatica.
Funzioni dei Convertitori di Media di Temperatura Industriale 10/100 a Fibra S-110-XT
Auto-Negotiation (802.3u) | Il convertitore di media supporta la funzione Auto-Negotiation sull'interfaccia 10/100Base-TX. |
Auto-MDIX | Quando è abilitata, la funzione Auto-MDIX (Automatic Medium-Dependant Interface Crossover) rileva i segnali sull'interfaccia 1000Base-T per determinare il tipo di cavo collegato (incrociato o passante diretto) e configura automaticamente la connessione. Con la funzione Auto-MDIX abilitata, il collegamento tra il convertitore di media e il dispositivo all'altra estremità del cavo si può effettuare sia mediante cavo passante diretto, sia mediante cavo incrociato. |
Link Pass-Through | Con la funzione Link Pass-Through, lo stato del ricevitore UTP viene passato al trasmettitore in fibra per rendere il convertitore di media trasparente per i dispositivi terminali collegati. Inoltre, se è abilitata la funzione Far-End Fault, il convertitore di media può disattivare il trasmettitore 10/100Base-TX quando riceve una segnalazione Far-End Fault. L'impiego congiunto delle funzioni Link Pass-Through e Far-End Fault riduce al minimo le perdite di dati in caso di guasto. Gli eventuali guasti vengono segnalati ai dispositivi terminali e questo semplifica la soluzione dei problemi. |
Far-End Fault (FEF) | Il convertitore di media implementa lo standard 802.3 per il Far-End Fault ai fini della segnalazione e rilevazione di condizioni di errore dei dispositivi remoti sulla connessione in fibra 100Base-X. Con questa funzione abilitata, il convertitore di media trasmette la segnalazione Far-End Fault attraverso la connessione su fibra 100Base-X ogni volta che viene rilevato un errore di ricezione sulla connessione. Il convertitore di media effettua un monitoraggio continuo dei segnali validi sulla connessione in fibra 100Base-X. Il comportamento del convertitore di media al ricevimento di una segnalazione Far-End Fault dipende dall'impostazione dello switch Link Pass-Through. |
Pause (IEEE 802.3xy) | La segnalazione delle pause è una funzione IEEE che sospende temporaneamente la trasmissione di dati tra due dispositivi nel caso in cui uno dei due sia sovraccarico. Il Convertitore di Media Fast Ethernet supporta la negoziazione Pause sulle connessioni in rame 100Base-TX. |
VLAN | Il convertitore di media è trasparente per i pacchetti con tag VLAN |
Loopback Remoto | Il convertitore di media è in grado di eseguire un loopback sulla porta in fibra ottica. |
Power | |
---|---|
Input Supply Voltage | 6 - 30 vDC, unregulated ( 12 vDC Nominal ) |
Current | 175 mA |
Power Consumption | 2.1 watts |
Power Connector | 2-pin fixed terminal block |
Indicators | |
Power / TST | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode. |
Fiber link on / Receive activity (LKF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received. |
Copper link on / Receive activity (LKC) | This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received. |
Fiber Duplex (FDF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is operatinal in full duplex mode. The LED is off when in half duplex. |
Copper Duplex (FDC) | This green LED is operational only when power is applied. The LED is on when the 10/100Base-TX link is operatinal in full duplex mode. The LED is off when in half duplex. |
10/100 Speed | This green LED is operational only when power is applied. The LED is on when the speed of the copper Ethernet port is running at 100 MBPS. The LED is off when in 10 MBPS |
Switches - accessible through a side opening in the chassis | |
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter
uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to
advertise full duplex. Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
Link Pass Through | Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter. When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on. Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface. |
Far-End Fault (FEF) | Enabled (Default) - The media converter transmits the Far-End
Fault Indication over the 100Base-X fiber connection whenever a receive
failure is detected on the 100Base-X fiber connection. The media converter
continuously monitors the100Base-X fiber connection and clears the Far-End
Fault Indication condition when a valid signal is received. Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection. |
Remote Loopback | The media converter can perform a loopback on the 100Base-X fiber
interface. Disabled (Default - Up) Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface. |
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the
HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u)
is disabled the Media converter will use the RX Energy method on the 100Base-TX
interface to set the port MDI or MDIX whichever is appropriate. Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
Speed Copper | 100 (Default) 10 |
Duplex Copper | Full (Default) Half |
Duplex Fiber | Full (Default) Half |
Connectors | |
100Base-TX | RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable |
Magnetic Isolation | 1.5kv |
Filtering | |
Filtering | 1024 MAC Addresses |
Frame Specifications | |
Buffer | 512 Kbits frame buffer memory |
Size | Maximum frame size of 2048 bytes |
Environmental Specifications | |
Operating Temperature | -40 C to 75 C (-40 F to 167 F) |
Storage Temperature | -40 C to 85 C (-40 F to 185 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output ( BTU/HR ) |
7.2 |
MTBF (Hours)* | 607,001 |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.3 kg, 0.66 lbs |
Dimensions | 120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches |
Packaging | |
Shipping Weight | 0.425 kg, .9 lbs |
Shipping Dimensions | 150 x 210 x 40 mm, 5.9 x 11 x 2.8 inches |
Regulatory Approvals | |
Emissions | FCC Part 15 Class B, EN55022 Class B |
CISPR 22 Class B CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | UL 60950-1 |
IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
|
CE | |
Laser Safety | EN 60825-1:2007 |
Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. | |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A991 |
HTSUS Number: 8517.62.0020 | |
Perle Limited Lifetime Warranty |
*Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Fast Ethernet a Telecamere IP |
---|
Connessione di Telecamere IP 10/100 a Dorsale Fast Ethernet I Convertitori di Media di temperatura estesa autonomi vengono posizionati in corrispondenza dell'estremità remota per collegare le telecamere ad interfaccia in rame con i cavi in fibra ottica. La fibra ottica consente di aumentare la distanza di connessione fino a 20 chilometri grazie ad una fibra monomodo o multimodo che arriva fino alla centrale operativa. Il telaio del convertitore di media ubicato nell'armadietto dati presso la centrale operativa accetta il segnale su fibra, lo converte e si collega all'apparecchiatura in rame della sede principale. ![]() |
Fibra Fast Ethernet a Punti di Accesso Wireless |
Connessione di Punti di Accesso Wireless 10/100 a Dorsale Fast Ethernet Quando gli AP sono utilizzati in ambienti industriali con condizioni climatiche problematiche caratterizzate da temperature estremamente alte o basse, i convertitori di media di temperatura estesa autonomi vengono posizionati in corrispondenza dell'estremità remota e collegano gli AP con interfaccia in rame ai cavi in fibra ottica. La fibra ottica consente di aumentare la distanza di connessione fino a 20 chilometri grazie ad una fibra monomodo o multimodo che arriva fino alla centrale operativa. Il telaio del convertitore di media ubicato nell'armadietto dati presso la centrale operativa accetta il segnale su fibra, lo converte e si collega all'apparecchiatura in rame della sede principale. ![]() |
Bridge i Dispositivi 10/100 a una Dorsale Gigabit |
Connessione di Dispositivi 10/100 a Dorsale Gigabit ![]() |
Monomodale / Fibra Singola |
Collegare le porte in rame mediante un cavo in fibra single strand (detto anche "Bi-Direzionale" o BiDi) ![]()
Tuttavia, per contenere i costi, o se la fibra disponibile è limitata, è possibile utilizzare la tecnologia WDM. La tecnologia WDM impiega frequenze di trasmissione e ricezione separate per comunicare attraverso cavi in fibra single strand. Questa tecnologia sfrutta il fatto che la fibra ottica è in grado di trasmettere fasci di luce a diverse lunghezze d'onda simultaneamente, senza che queste interagiscano tra loro. In questo modo, una fibra singola è in grado di trasportare diversi segnali o canali su lunghezze d'onda differenti simultaneamente. Quindi, se si utilizzano cavi in fibra single strand, è necessario installare un convertitore di media di tipo "Up" a un'estremità e un media converter di tipo "Down" all'altra per garantire la conversione da rame a fibra. Perle offre un'ampia varietà di media converter ("Up/Down") a fibra singola per il collegamento di 10BaseT, Fast Ethernet e Gigabit a cavi in fibra single strand. Sia che vi occorra una versione gestita o non gestita, standalone o con telaio modulare, da 20 o 120 km, Perle è in grado di offrirvi il modello più adatto a soddisfare le vostre esigenze di conversione in fibra. |
Select a Model to obtain a Part Number - S-110-XT Industrial Temperature Media Converter 10/100 to Fiber
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110-M2ST2-XT | Dual ST |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-M2SC2-XT | Dual SC |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-M2LC2-XT | Dual LC |
100Base-FX |
-20.0 |
-12.0 |
-30.0 |
-14.0 |
10.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-110-S2ST20-XT | Dual ST |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2SC20-XT | Dual SC |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-110-S2LC20-XT | Dual LC |
100Base-LX |
-15.0 |
0.0 |
-34.0 |
-5.0 |
19.0 |
1310 |
SMF |
20 km (12.4 mi) |
Single Fiber Models Recommended use in pairs
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110-S1SC20U-XT | Single SC |
100Base-BX |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km (12.4 mi) |
S-110-S1SC20D-XT | Single SC |
100Base-BX |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km (12.4 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*Based on use with 62.5/125 micron multimode fiber.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |
04030674 | Extended Temperature USA power adapter for 12 Volt Industrial Temperature Media Converter |
04030671 | Extended Temperature UK power adapter for 12 Volt Industrial Temperature Media Converter |
04030672 | Extended Temperature EU power adapter for 12 Volt Industrial Temperature Media Converter |
04030675 | Extended Temperature SA power adapter for 12 Volt Industrial Temperature Media Converter |
04030676 | Extended Temperature AUS power adapter for 12 Volt Industrial Temperature Media Converter |