Convertitore di Media PoE/SFP S-110
Conversione da 10/100Base-TX a 100Base-X
- Altri moduli SFP standard di settore
- Fibra da 10/100Base-TX a 100Base-X
- Alimentazione PSE IEEE 802.3 PoE e PoE+
- Compatibile con dispositivi legacy pre-standard PoE
- Funzionalità avanzate: riavvio PD, Smart Link Pass-Through, Fiber Fault Alert, Auto-MDIX e Loopback
I Convertitori di Media PoE a conversione di velocità Fast Ethernet di Perle, ricchi di funzioni, consentono di collegare in modo trasparente il rame alla fibra, fornendo al contempo tecnologia Power over Ethernet (PoE) a dispositivi compatibili, basati sugli standard PoE e PoE+, quali videocamere IP, telefoni VoIP e punti di accesso wireless. I Convertitori di Media PoE S-110 sono anche disponibili modelli con supporto per gamme di temperature operative più estese. Oltre 40 modelli tra cui scegliere, con porte fissi in fibra o SFP. Il porta in fibra ottica pluggable consente una configurazioni di rete flessibili utilizzando il transceivers SFP forniti da Perle, Cisco o di altri produttori di SFP compatibile MSA.
I Convertitori di Media PoE di Perle sono classificati come Power Sourcing Equipment (PSE). Utilizzando cavi UTP standard per la trasmissione di dati via Ethernet, i convertitori di media PoE di Perle sono in grado di fornire alimentazione a uno Powered Device (PD). Perle offre modelli di convertitori di media PoE che supportano sia lo standard PoE IEEE 802.3af (15,4 W di potenza) che lo standard PoE+ IEEE 802.3at (30 W di potenza). Per saperne di più sulla tecnologia PoE.
I Convertitori di Media PoE 10/100 da Ethernet a Fibra di Perle rappresentano una soluzione economica per aumentare l'estensione di una rete esistente mediante il cablaggio in fibra. Al contempo, essi fungono da iniettori PoE per l'alimentazione di dispositivi quali telefoni IP, apparecchiature per videoconferenze, videocamere IP e dispositivi Wi-Fi collegati mediante cavi UTP in rame.
Gli amministratori di rete sono in grado di "vedere tutto" grazie a funzioni avanzate quali Auto-Negotiation, Auto-MDIX, Link Pass-Through, Fiber Fault Alert e Loopback. Ciò garantisce una maggiore efficienza nella soluzione dei problemi e minore necessità di manutenzione in loco. Funzioni come queste, che consentono di risparmiare tempo e denaro, garanzia a vita e assistenza tecnica gratuita in tutto il mondo fanno dei Convertitori di Media PoE a Conversione di Velocità Fast Ethernet di Perle una scelta intelligente per i professionisti dell'informatica.
Funzionalità dei Convertitori di Media PoE a Conversione di Velocità da Fast Ethernet a Fibra
Power Over Ethernet ( PSE ) |
Funge da Power Sourcing Equipment (PSE) per dispositivi compatibili con IEEE 802.3af (PoE a 15,4 watt) e IEEE 802.3at (PoE+ fino a 30 watt). Disponibile nella versione PoE e PoE+. I modelli PoE+ supportano sia dispositivi PD di tipo 1 (PoE) che di tipo 2 (PoE+). |
Gestione dell'alimentazione avanzata |
|
Riavvio PD |
Ideale per il riavvio in remoto delle apparecchiature, questa funzionalità configurabile consente di eseguire un momentaneo ripristino dell'alimentazione del Powered Device (PD) collegato. Se abilitata, il convertitore di media provvederà, in caso di perdita del segnale RX in fibra, a disattivare l'alimentazione PSE in uscita fornita al dispositivo PD per 2 secondi, quindi a riattivarla e lasciarla attiva fino alla successiva perdita di un collegamento RX in fibra (dopo il precedente ripristino). Se disabilitata, la perdita di un link RX in fibra non avrà alcun effetto sull'alimentazione PSE fornita ai PD. |
Supporto PD |
È garantito il supporto di un'ampia gamma di PD (Powered Device).
|
Fascetta pressacavi | Tutti i modelli sono provvisti di una fascetta pressacavi che garantisce una connessione sicura al convertitore di media. Ideale per ambienti soggetti a vibrazioni. |
Auto-Negotiation (802.3u) | Il convertitore di media supporta la negoziazione automatica sull'interfaccia 10/100Base-TX. |
Auto-MDIX | Quando è abilitata, la funzione Auto-MDIX (Automatic Medium-Dependant Interface Crossover) rileva i segnali sull'interfaccia 1000Base-T per determinare il tipo di cavo collegato (incrociato o passante diretto) e configura automaticamente la connessione. Con la funzione Auto-MDIX abilitata, il collegamento tra il convertitore di media e il dispositivo all'altra estremità del cavo si può effettuare sia mediante cavo passante diretto, sia mediante cavo incrociato. |
Link Pass-Through |
Con la funzione Link Pass-Through, lo stato del ricevitore UTP viene passato al trasmettitore in fibra per rendere il convertitore di media trasparente per i dispositivi terminali collegati. Inoltre, se è abilitata la funzione Far-End Fault, il convertitore di media può disattivare il trasmettitore 10/100Base-TX quando riceve una segnalazione Far-End Fault. L'impiego congiunto delle funzioni Link Pass-Through e Far-End Fault riduce al minimo le perdite di dati in caso di guasto. Gli eventuali guasti vengono segnalati ai dispositivi terminali e questo semplifica la soluzione dei problemi. |
Far-End Fault (FEF) |
Il convertitore di media implementa lo standard 802.3 per il Far-End Fault ai fini della segnalazione e rilevazione di condizioni di errore dei dispositivi remoti sulla connessione in fibra 100Base-FX. Con questa funzione abilitata, il convertitore di media trasmette la segnalazione Far-End Fault attraverso la connessione su fibra 100Base-FX ogni volta che viene rilevato un errore di ricezione su tale connessione. Il convertitore di media effettua una rilevazione continua del segnale valido sulla connessione in fibra 100Base-FX. Il comportamento del convertitore di media al ricevimento di una segnalazione Far-End Fault dipende dall'impostazione dello switch Link Pass-Through. |
Pause (IEEE 802.3xy) | La segnalazione delle pause è una funzione IEEE che sospende temporaneamente la trasmissione di dati tra due dispositivi nel caso in cui uno dei due sia sovraccarico. Il convertitore di media supporta la negoziazione Pause sulle connessioni in rame 10/100Base-TX. |
Duplex | È supportato il funzionamento in full e half duplex. |
VLAN | Trasparente per i pacchetti con tag VLAN. |
Loopback remoto | In grado di eseguire un loopback sull'interfaccia in fibra 100Base-X. |
Non è quello che stai cercando? Visualizza tutti i Convertitori di Media in Fibra Perle.
Hai bisogno di aiuto? Contatta Perle.
Hardware Specifications
Power | |||||||||
---|---|---|---|---|---|---|---|---|---|
Input Supply Voltage | PoE models: 46 - 57 vDC PoE+ models: 52 - 57 vDC |
||||||||
Power Consumption | 3.5 Watts | ||||||||
Power Over Ethernet (PSE) | PoE models: maximum to 15.4 watts supplied to port PoE+ models: up to 30 watts supplied to port |
||||||||
PoE Options | Alternative A (power on pins 1,2 and 3,6)
Alternative B (power on pins 4,5 and 7,8) Legacy PoE (IE VoIP phones and wireless access points) - (reverse polarity on pins 4,5 and 7,8) Legacy large capacitor detect (pins 4,5 and 7,8) |
||||||||
Power Connector | 5.5mm x 9.5mm x 2.1mm barrel socket | ||||||||
Power Adapter | |||||||||
Universal AC/DC adapter | 100-240v AC, regulated 48vDC adapter included for PoE 100-240v AC, regulated 56vDC adapter included for PoE+ |
||||||||
Indicators | |||||||||
Power (PWR) | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink slowly when either fiber port is in Loopback test mode. The LED will blink quickly if there is a hardware failure where the reason code can be identified through a various blinking cycles. | ||||||||
Fiber link on / Receive activity (LKF 1/2) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the fiber port
If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared. |
||||||||
Copper link on / Receive activity (LKC 1/2) |
This green LED is operational only when power is applied. The LED will blink along with transmit/receive data on the 10/100/1000 UTP port
If a loss of link on the copper port results in a Link Passthrough condition to the fiber port, this LED will blink at a rate of once every 2 seconds until the condition is cleared. |
||||||||
10/100 Speed | This green LED is operational only when power is applied. The LED is green when the speed of the copper ethernet port is running at 100 Mbps. The LED is off when in 10 Mbps. | ||||||||
PSE Status | This LED will signify the status of the PSE function. Using multi-color and blinking the unit will show the following status for the PSE;
GREEN — Solid: The PSE has successfully detected a compliant PD and is applying power over the UTP (for legacy pin out simply show active power when applied) YELLOW — Solid: The PSE is not active. This means the PSE has been configured to provide power, but the PD is :
OFF — PSE function switch disabled RED — Blinking: Error Conditions
|
||||||||
Switches | |||||||||
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex. Disabled - The media converter sets the port according to the position of the speed and duplex switches. |
||||||||
Link Pass Through | Disabled (Default) - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface. Enabled - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter. When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on. |
||||||||
Far-End Fault (FEF) | Enabled (Default) - The media converter transmits the Far-End Fault Indication over the 100Base-X fiber connection whenever a receive failure is detected on the 100Base-X fiber connection. The media converter continuously monitors the100Base-X fiber connection and clears the Far-End Fault Indication condition when a valid signal is received. Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection. |
||||||||
Remote Loopback | The media converter can perform a loopback on the 100Base-X fiber interface.
Disabled (Default - Up) Enabled- The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface. |
||||||||
Speed Copper (internal strap) | 100 (Default) 10 |
||||||||
Duplex Copper (internal strap) | Full (Default) Half |
||||||||
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter determines the current cable pinout to use on the copper interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the copper interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media converter's transmitter and the partner devices transmitter are connected to the others receiver. The Media converter's 100Base-TX port is configured as MDI-X with this switch setting. |
||||||||
PSE Power | When enabled (UP), the media converter will perform a Power Sourcing Equipment (PSE) function as per IEEE802.3af or 802.3at standards (relevant model).
Default is "enabled" |
||||||||
PD Power Reset | This is a technique to perform a power reset on a PD device attached.
When enabled (down), the media converter will upon loss of link on any fiber port, turn off PSE output power to the PD device for 2 seconds then turn the power back on. The power remains on until any fiber link transitions from up to down again. With Passthrough enabled, a loss of link on the fiber resulting from a loss of link on the copper, a PD Power Reset will occur and the copper link will continue to reflect the state of the fiber link. When PD Power Reset disabled, loss of fiber link has no effect on PSE power to the PD device. |
||||||||
PoE Power Options (Internal Straps) |
Set to Alternative A (default): Pins 3,6 Neg, Pins 1,2 Pos Set to Alternative B: Pins 7,8 Neg, Pins 4,5 Pos Set to Legacy Pre-Standard: Pins 7,8 Pos, Pins 4,5 Neg |
||||||||
Connectors | |||||||||
10/100Base-TX | RJ45 connector. 2 pair CAT5, EIA/TIA 568A/B or better cable for 10/100. |
||||||||
Magnetic Isolation | 1.5kv | ||||||||
Fixed Fiber | Dual multimode or single mode (Duplex) fiber - SC, ST
Single strand fiber (Simplex) - SC LC - obtained by inserting an SFP (LC) in an SFP slot model |
||||||||
Small Form Factor Pluggable (SFP) slot |
SFP slot models: Empty slot for 100Base-X SFP modules supplied by Perle, Cisco or other manufacturers of MSA compliant SFPs.
Hot insertion and removable (hot swappable). |
||||||||
Filtering | |||||||||
Filtering | 1024 MAC Addresses | ||||||||
Frame Specifications | |||||||||
Buffer | 1000 Kbits frame buffer memory | ||||||||
Size | Maximum frame size of 2048 bytes | ||||||||
Environmental Specifications | |||||||||
Operating Temperature | 0 C to 50 C (32 F to 122 F) | ||||||||
Storage Temperature | minimum range of -25 C to 70 C (-13 F to 158 F) | ||||||||
Operating Humidity | 5% to 90% non-condensing | ||||||||
Storage Humidity | 5% to 95% non-condensing | ||||||||
Operating Altitude | Up to 3,048 meters (10,000 feet) | ||||||||
Heat Output (BTU/HR) |
12 | ||||||||
MTBF (Hours)* |
|
||||||||
Chassis | Metal with an IP20 ingress protection rating | ||||||||
Mounting | |||||||||
Din Rail Kit | Optional | ||||||||
Rack Mount Kit | Optional | ||||||||
Product Weight and Dimensions | |||||||||
Weight | 0.3 Kg, 0.7 lbs (No power adapter) | ||||||||
Dimensions | 120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches | ||||||||
Packaging | |||||||||
Shipping Weight | PoE models : 1 kg, 2.2 lbs PoE+ models : 1.3Kg, 2.9 lbs |
||||||||
Shipping Dimensions | 300 x 200 x 70mm, 11.8 x 7.9 x 2.8 inches | ||||||||
Regulatory Approvals | |||||||||
Emissions | FCC Part 15 Class A, EN55022 Class A | ||||||||
CISPR 22 Class A CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
|||||||||
EN61000-3-2 | |||||||||
Immunity | EN55024 | ||||||||
Electrical Safety | UL/EN/IEC 62368-1 CAN/CSA C22.2 No. 62368-1 |
||||||||
UL 60950-1 IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
|||||||||
CE | |||||||||
Laser Safety | EN 60825-1 Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. |
||||||||
Environmental | Reach, RoHS and WEEE Compliant | ||||||||
Other | ECCN: 5A991 | ||||||||
HTSUS Number: 8517.62.0020 | |||||||||
Perle Limited Lifetime Warranty |
*Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Fibra Fast Ethernet per Videocamere IP |
---|
Connessione di videocamere IP 10/100 a una dorsale Gigabit La fibra viene implementata da un data closet esistente a un'area con accesso all'alimentazione. Un convertitore di media PoE, alimentato a 48 V CC oppure con tensione standard da 100-240 V CA, viene collegato all'alimentazione elettrica e al cavo in fibra. L'estensione della rete Ethernet in rame (su cavo UTP o STP) può così essere aumentata di altri 100 metri verso la videocamera IP. Il convertitore di media PoE provvede alla conversione dei dati dalla fibra al rame, integrando l'alimentazione da trasmettere alla videocamera di sicurezza. |
Fibra Fast Ethernet per Punti di Accesso Wireless |
Connessione di punti di accesso wireless 10/100 a una dorsale Fast Ethernet La fibra viene implementata da un data closet esistente a un'area con accesso all'alimentazione. Un convertitore di media PoE, alimentato a 48 V CC oppure con tensione standard da 100-240 V CA, viene collegato all'alimentazione elettrica e al cavo in fibra. L'estensione della rete Ethernet in rame (su cavo UTP o STP) può così essere aumentata di altri 100 metri verso il punto di accesso wireless. Il convertitore di media PoE provvede alla conversione dei dati dalla fibra al rame, integrando l'alimentazione da trasmettere al punto di accesso wireless. |
Fibra Fast Ethernet per Workstation desktop/telefoni VoIP (Voice over IP) |
Connessione di workstation e telefoni VoIP 10/100 a una dorsale Fast Ethernet Per telefoni VoIP contenenti dispositivi di trasmissione radio duplici, che richiedono più di 15,4 watt di potenza, sono disponibili anche modelli PoE+ in grado di arrivare fino a 30 watt. La fibra viene implementata da un data closet esistente a un'area con accesso all'alimentazione. Un convertitore di media PoE, alimentato a 48 V CC oppure con tensione standard da 100-240 V CA, viene collegato all'alimentazione elettrica e al cavo in fibra. L'estensione della rete Ethernet in rame (su cavo UTP o STP) può così essere aumentata di altri 100 metri verso il telefono VoIP. Il convertitore di media PoE provvede alla conversione dei dati dalla fibra al rame, integrando l'alimentazione da trasmettere al telefono VoIP. |
Fibra Singola/Monomodo |
Collegamento di porte in rame mediante un cavo in fibra single strand (detto anche "Bi-Direzionale" o BiDi). S-110P-S1SC10US-110P-S1SC10D
Tuttavia, per contenere i costi, o se la fibra disponibile è limitata, è possibile utilizzare la tecnologia WDM. La tecnologia WDM impiega frequenze di trasmissione e ricezione separate per comunicare attraverso cavi in fibra single strand. Questa tecnologia sfrutta il fatto che la fibra ottica è in grado di trasmettere fasci di luce a diverse lunghezze d'onda simultaneamente, senza che queste interagiscano tra loro. In questo modo, una fibra singola è in grado di trasportare diversi segnali o canali su lunghezze d'onda differenti simultaneamente. Quindi, se si utilizzano cavi in fibra single strand, è necessario installare un convertitore di media di tipo "Up" a un'estremità e un convertitore di media di tipo "Down" all'altra per garantire la conversione da rame a fibra. |
Select a Model to obtain a Part Number - 10/100 PoE Media Converter
Model |
Fiber Port
Connector |
Type |
Transmit
(dBm) |
Receive
(dBm) |
Power
Budget (dBm) |
Wavelength
(nm) |
Fiber
Type |
Operating
Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110P-SFP | 1 x SFP / LC |
100Base-X |
- |
- |
- |
- |
- |
- |
MMF/SMF |
- |
S-110P-M2SC2 | Dual SC |
100Base-FX |
-20.0 |
-12.0 |
-31 |
-14.0 |
11.0* |
1310 |
MMF |
2 km
(1.2 mi) |
S-110P-M2ST2 | Dual ST |
100Base-FX |
-20.0 |
-12.0 |
-31 |
-14.0 |
11.0* |
1310 |
MMF |
2 km
(1.2 mi) |
S-110P-S2SC20 | Dual SC |
100Base-LX |
-18.0 |
-7.0 |
-32 |
-3.0 |
14.0 |
1310 |
SMF |
20 km
(12.4 mi) |
S-110P-S2ST20 | Dual ST |
100Base-LX |
-18.0 |
-7.0 |
-32 |
-3.0 |
14.0 |
1310 |
SMF |
20 km
(12.4 mi) |
S-110P-S2SC40 | Dual SC |
100Base-EX |
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1310 |
SMF |
40 km
(25 mi) |
S-110P-S2ST40 | Dual ST |
100Base-EX |
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1310 |
SMF |
40 km
(25 mi) |
S-110P-S2SC80 | Dual SC |
100Base-ZX |
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1550 |
SMF |
80 km
(50 mi) |
S-110P-S2ST80 | Dual ST |
100Base-ZX
|
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1550 |
SMF
|
80 km
(50 mi) |
S-110P-S2SC120 | Dual SC |
100Base-ZX
|
0.0 |
-5.0 |
-35 |
-3.0 |
35.0 |
1550 |
SMF
|
120 km
(75 mi) |
S-110P-S2ST120 | Dual ST |
100Base-ZX
|
0.0 |
-5.0 |
-35 |
-3.0 |
35.0 |
1550 |
SMF |
120 km
(75 mi) |
Single Fiber Models Recommended use in pairs
Model |
Fiber Port
Connector |
Type |
Transmit
(dBm) |
Receive
(dBm) |
Power
Budget (dBm) |
Wavelength
(nm) |
Fiber
Type |
Operating
Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110P-M1ST2U | Single ST |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km
(1.2 mi) |
S-110P-M1ST2D | Single ST |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km
(1.2 mi) |
S-110P-M1SC2U | Single SC |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km
(1.2 mi) |
S-110P-M1SC2D | Single SC |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km
(1.2 mi) |
S-110P-S1ST20U | Single ST |
100Base-BX-U |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km
(12.4 mi) |
S-110P-S1ST20D | Single ST |
100Base-BX-D |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km
(12.4 mi) |
S-110P-S1SC20U | Single SC |
100Base-BX-U |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km
(12.4 mi) |
S-110P-S1SC20D | Single SC |
100Base-BX-D |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km
(12.4 mi) |
S-110P-S1SC40U | Single SC |
100Base-BX-U |
-8.0 |
-3.0 |
-33 |
-3.0 |
25.0 |
1310 / 1550 |
SMF |
40 km
(25 mi) |
S-110P-S1SC40D | Single SC |
100Base-BX-D |
-8.0 |
-3.0 |
-33 |
-3.0 |
25.0 |
1550 / 1310 |
SMF |
40 km
(25 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*Based on use with 65.5/125 micron multimode fiber.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |
Select a Model to obtain a Part Number - 10/100 PoE+ Media Converter
Model |
Fiber Port
Connector |
Type |
Transmit
(dBm) |
Receive
(dBm) |
Power
Budget (dBm) |
Wavelength
(nm) |
Fiber
Type |
Operating
Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110PP-SFP | 1 x SFP / LC |
100Base-X |
- |
- |
- |
- |
- |
- |
MMF/SMF |
- |
S-110PP-M2SC2 | Dual SC |
100Base-FX |
-20.0 |
-12.0 |
-31 |
-14.0 |
11.0* |
1310 |
MMF |
2 km
(1.2 mi) |
S-110PP-M2ST2 | Dual ST |
100Base-FX |
-20.0 |
-12.0 |
-31 |
-14.0 |
11.0* |
1310 |
MMF |
2 km
(1.2 mi) |
S-110PP-S2SC20 | Dual SC |
100Base-LX |
-18.0 |
-7.0 |
-32 |
-3.0 |
14.0 |
1310 |
SMF |
20 km
(12.4 mi) |
S-110PP-S2ST20 | Dual ST |
100Base-LX |
-18.0 |
-7.0 |
-32 |
-3.0 |
14.0 |
1310 |
SMF |
20 km
(12.4 mi) |
S-110PP-S2SC40 | Dual SC |
100Base-EX |
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1310 |
SMF |
40 km
(25 mi) |
S-110PP-S2ST40 | Dual ST |
100Base-EX |
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1310 |
SMF |
40 km
(25 mi) |
S-110PP-S2SC80 | Dual SC |
100Base-ZX |
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1550 |
SMF |
80 km
(50 mi) |
S-110PP-S2ST80 | Dual ST |
100Base-ZX
|
-5.0 |
0.0 |
-34 |
-3.0 |
29.0 |
1550 |
SMF
|
80 km
(50 mi) |
S-110PP-S2SC120 | Dual SC |
100Base-ZX
|
0.0 |
-5.0 |
-35 |
-3.0 |
35.0 |
1550 |
SMF
|
120 km
(75 mi) |
S-110PP-S2ST120 | Dual ST |
100Base-ZX
|
0.0 |
-5.0 |
-35 |
-3.0 |
35.0 |
1550 |
SMF |
120 km
(75 mi) |
Single Fiber Models Recommended use in pairs
Model |
Fiber Port
Connector |
Type |
Transmit
(dBm) |
Receive
(dBm) |
Power
Budget (dBm) |
Wavelength
(nm) |
Fiber
Type |
Operating
Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-110PP-M1ST2U | Single ST |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km
(1.2 mi) |
S-110PP-M1ST2D | Single ST |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km
(1.2 mi) |
S-110PP-M1SC2U | Single SC |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km
(1.2 mi) |
S-110PP-M1SC2D | Single SC |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km
(1.2 mi) |
S-110PP-S1ST20U | Single ST |
100Base-BX-U |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km
(12.4 mi) |
S-110PP-S1ST20D | Single ST |
100Base-BX-D |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km
(12.4 mi) |
S-110PP-S1SC20U | Single SC |
100Base-BX-U |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km
(12.4 mi) |
S-110PP-S1SC20D | Single SC |
100Base-BX-D |
-14.0 |
-8.0 |
-32 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km
(12.4 mi) |
S-110PP-S1SC40U | Single SC |
100Base-BX-U |
-8.0 |
-3.0 |
-33 |
-3.0 |
25.0 |
1310 / 1550 |
SMF |
40 km
(25 mi) |
S-110PP-S1SC40D | Single SC |
100Base-BX-D |
-8.0 |
-3.0 |
-33 |
-3.0 |
25.0 |
1550 / 1310 |
SMF |
40 km
(25 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*Based on use with 62.5/125 micron multimode fiber.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |