eX-S1110 – Estensori Gigabit Ethernet

Estensore Rame 10/100/1000 Ethernet

Estensori Ethernet 10/100/1000
  • Ampliate la comunicazione 10/100/1000Base-T Ethernet fino a 3 chilometri su doppino telefonico 24 a 2 cavi
  • Alta velocità: velocità di linea aggregata fino a 200+ mbps
  • Funzionamento trasparente per tutti i protocolli Ethernet inclusi i pacchetti 802.1Q VLAN e gli schemi di compressione video IP
  • Una o quattro porte 10/100/1000 Ethernet
  • Funzionalità avanzate: Link Pass-Through*, Interlink Fault Feedback*, Plug and Play, Auto-MDIX e Loopback
Richiedi preventivo Aggiungi a Preferiti
Ethernet eX-1S1110 eX-4S1110
Port 1 port RJ45 – 10/100/1000 Base-T - Shielded 4 port RJ45 – 10/100/1000 Base-T - Shielded
Auto-MDIX Auto-MDIX enables proper operation with either straight-through or crossover cabling
Distance Distance up to 100 meters ( 328 feet ) as per IEEE 802.3
Maximum Frame Size 1522 bytes
VDSL – Interlink
RJ45, BNC, Terminal Block TIP and RING are polarity insensitive. Surge suppression of 400 volts between TIP and RING Choice of RJ45, BNC or terminal block models for VDSL link connector
  • RJ45 – RING pin 4, TIP pin 5 (TIA 568 A/B)
  • BNC – Coaxial 50 and 75 ohm cable with BNC connector
  • Terminal Block – 2 position screw connectors for use with twisted pair telephone cabling
Cabling Ethernet Extenders must be connected in pairs using unconditioned wire between 19 ( 0.9 mm ) and 26 AWG ( 0.44 mm ). Circuits that run through signal equalization equipment are not permitted.
VDSL2 Line Rate/Reach Actual distance and rates experienced will depend on condition and gauge of wire used. This Rate/Reach table applies to 24 AWG ( 0.5 MM ) twisted pair wiring on RJ45 (RJ) and terminal block (TB) models.
High Speed Asymmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 101 92
1000 305 101 63
1500 457 90 38
2000 610 62 24
2500 762 55 10
3000 914 42 5
3500 1000 35 3
High Speed Symmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 101 101
1000 305 85 101
1500 457 62 47
2000 610 60 29
2500 762 44 14
3000 914 30 7
3500 1000 29 4
Long Reach Symmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 53 44
1000 305 53 43
2500 762 39 18
4000 1219 25 4
5500 1676 17 1.9
7000 2134 8 2.3
7500 2286 7 2.2
8000 2438 5 2.2
Long Reach Asymmetric
Reach ( Distance ) VDSL Rate ( Mbps )
feet meters Downstream Upstream
500 152 78 16
1000 305 78 16
2500 762 55 10
4000 1219 31 0.8
5500 1676 20 0.6
7000 2134 11 0.6
7500 2286 10 0.6
8000 2438 8 0.6
Power eX-1S1110 eX-4S1110
Input Supply Voltage 9 - 30 vDC, unregulated ( 12 vDC Nominal )
Current 350 mA 500 mA
Power Consumption 4.2 watts 6 watts
Power Connectors 5.5mm x 9.5mm x 2.1mm barrel socket and 2 pin terminal Block
Power Adapter
Universal AC/DC adapter 100-240v AC, regulated 12V DC adapter included
Indicators
Power / TST This green LED is turned on when power is applied to the Ethernet Extender. Otherwise it is off. The LED will blink when in Loopback test mode.
CO - Local Ethernet Extender is operating in CO VDSL mode
CPE - remote Ethernet Extender is operating in CPE VDSL mode
ILNK Indicates Link Status and activity on the Interlink (VDSL) port
ETH Indicates link status and activity on Ethernet port(s).
Switches eX-1S1110 eX-4S1110
Access All switch settings are accessible through a side opening in the chassis
Rate/Reach Two switches enable the user to select the right balance between speed and distance for their environment.
Signal to Noise Ratio Selectable Signal to Noise Ratio (SNR) of 6dB or 9dB. The higher SNR number provides better impulse noise protection but lowers performance.
Auto-Negotiation (802.3u) Enabled (Default) - The Ethernet Extender uses 802.3u Auto-negotiation on the 10/100/1000Base-T interface. It is set to advertise full duplex.

Disabled - The Ethernet Extender sets the port according to the position of the speed and duplex switches.
Link Mode Standard (Default)– The 10/100/1000 Base-T link remains active independent of the state of the Ethernet link on its remote peer.

Link Pass-Through - the state of the 10/100/1000 Base-T Ethernet connection is "passed through" or propagated across the VDSL link to the 10/100/1000 Base-T Ethernet link on its remote Ethernet Extender peer. This enables a managed switch to report the state of the remote device to its network management system.

 N/A
Interlink Fault Feedback Enabled - A loss of VDSL link will drop the 10/100/1000 Ethernet port on each end until the link recovers.

Disabled ( Default ) – The state of the VDSL link is not propagated to the 10/100/1000 Base-T port

 N/A
Loopback Enabled - The VDSL interlink will perform a loopback function, retransmitting all received Ethernet frames back to its peer.

Disabled (Default - Up)
Set Ethernet Speed (Port 1) When Auto-Negotiation switch is disabled, fixed speed can be set at 100 (Default) or 10
Set Ethernet Duplex (Port 1) When Auto-Negotiation switch is disabled, Duplex can be set at Full (Default) or Half
Environmental Specifications eX-1S1110 eX-4S1110
Operating Temperature 0 C to 50 C (32 F to 122 F)
Storage Temperature minimum range of -25 C to 70 C (-13 F to 158 F)
Operating Humidity 5% to 90% non-condensing
Storage Humidity 5% to 95% non-condensing
Operating Altitude Up to 3,048 meters (10,000 feet)
Heat Output ( BTU/HR ) 14.3 20.5
MTBF (Hours)** Without power adaptor: 468,351
With power adaptor: 289,015		 365,542
207,212
Mounting
Din Rail Kit Optional
Rack Mount Kit Optional
Product Weight and Dimensions
Weight 0.3 kg, 0.66 lbs 0.47 kg, 1.04 lbs
Dimensions 120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches 130 x 115 x 26 mm, 5.1 x 4.5 x 1.0 inches
Packaging
Shipping Weight 0.55 kg, 1.2 lbs 0.75 kg, 1.7 lbs
Shipping Dimensions 170 x 260 x 70 mm, 6.7 x 10.2 x 2.8 inches
Regulatory Approvals
Emissions FCC Part 15 Class A, EN55022 Class A
CISPR 32:2015/EN 55032:2015 (Class A)
EN61000-3-2
Immunity CISPR 24:2010/EN 55024:2010
Electrical Safety UL 60950-1
IEC 60950-1(ed 2); am1, am2
EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013
CE
Environmental Reach, RoHS and WEEE Compliant
Other ECCN: 5A991
HTSUS Number: 8517.62.0050
Perle Lifetime warranty

*Available on 1 port models.
**Calculation model based on MIL-HDBK-217-FN2 @ 30 °C

Torna su