Convertitore Fast Ethernet S-100
Conversione in Modalità Fibra 100Base-TX a 100Base-FX

- Convertitore di Media per fibra da 100Base-TX a 100Base-FX
- Aumento dell'estensione delle reti fino a 120 km
- Media Converter SC, LC e ST
- Funzioni avanzate - Link Pass-Through, Far-End Fault, Auto-MDIX
La linea completa di Convertitori Perle Fast Ethernet collega in modo trasparente cavi UTP in rame a cavi in fibra. I nostri convertitori di media Fast Ethernet rappresentano una soluzione economica per aumentare l'estensione di una rete esistente, la durata delle apparecchiature non su fibra ottica o la distanza fra due dispositivi.
Le funzioni avanzate dei prodotti Perle sono una garanzia per gli amministratori di rete: Auto-Negotiation (negoziazione automatica), Auto-MDIX (Automatic Medium Dependent Interface Crossover, crossover automatico dell'interfaccia dipendente dal supporto fisico), Link Pass-Through, Far End Fault (segnalazione perdita di connessione remota) e Pause (pausa) rendono completamente trasparente il collegamento end to end e assicurano quindi una maggiore efficienza nella soluzione dei problemi e minore manutenzione in loco. Funzioni come queste, che consentono di risparmiare tempo e denaro, garanzia a vita e assistenza tecnica gratuita in tutto il mondo fanno dei Convertitori di Media Fast Ethernet di Perle una scelta intelligente per i professionisti dell'informatica.
Funzioni dei Convertitori Fast Ethernet: da 100Base-TX a 100Base-FX
Auto-Negotiation (802.3u) | Il convertitore di media supporta la negoziazione automatica sull'interfaccia Fast Ethernet 100Base-TX. |
Auto-MDIX | Quando è abilitata, la funzione Auto-MDIX (Automatic Medium-Dependant Interface Crossover) rileva i segnali sull'interfaccia 1000Base-T per determinare il tipo di cavo collegato (incrociato o passante diretto) e configura automaticamente la connessione. Con la funzione Auto-MDIX abilitata, il collegamento tra il convertitore di media e il dispositivo all'altra estremità del cavo si può effettuare sia mediante cavo passante diretto, sia mediante cavo incrociato. |
Link Pass-Through | Con la funzione Link Pass-Through, lo stato del ricevitore 100Base-TX viene passato al trasmettitore 100Base-FX per rendere il convertitore di media trasparente per i dispositivi terminali collegati. Inoltre, se è abilitata la funzione Far-End Fault, il convertitore di media può disattivare il trasmettitore 100Base-TX quando riceve una segnalazione Far-End Fault. L'impiego congiunto delle funzioni Link Pass-Through e Far-End Fault riduce al minimo le perdite di dati in caso di guasto. Gli eventuali guasti vengono segnalati ai dispositivi terminali e questo semplifica la soluzione dei problemi. |
Far-End Fault (FEF) | Il convertitore di media implementa lo standard 802.3 per il Far-End Fault ai fini della segnalazione e rilevazione di condizioni di errore dei dispositivi remoti sulla connessione in fibra 100Base-FX. Con questa funzione abilitata, il convertitore di media trasmette la segnalazione Far-End Fault attraverso la connessione su fibra 100Base-FX ogni volta che viene rilevato un errore di ricezione su tale connessione. Il convertitore di media effettua una rilevazione continua del segnale valido sulla connessione in fibra 100Base-FX. Il comportamento del convertitore di media al ricevimento di una segnalazione Far-End Fault dipende dall'impostazione dello switch Link Pass-Through. |
Pause (IEEE 802.3xy) | La segnalazione delle pause è una funzione IEEE che sospende temporaneamente la trasmissione di dati tra due dispositivi nel caso in cui uno dei due sia sovraccarico. Il Convertitore di Media Fast Ethernet supporta la negoziazione Pause sulle connessioni in rame 100Base-TX. |
VLAN | Il convertitore di media è trasparente per i pacchetti con tag VLAN. |
Power | |
---|---|
Input Supply Voltage | 6 - 30 vDC, unregulated ( 12 vDC Nominal ) |
Current | 167 mA |
Power Consumption | 2.0 watts |
Power Connector | 5.5mm x 9.5mm x 2.1mm barrel socket |
Power Adapter | |
Universal AC/DC Adapter | 100-240v AC, regulated DC adapter included |
Indicators | |
Power / TST | This green LED is turned on when power is applied to the media converter. Otherwise it is off. The LED will blink when in Loopback test mode. |
Fiber link on / Receive activity (LKF) | This green LED is operational only when power is applied. The LED is on when the 100Base-FX link is on and flashes with a 50% duty cycle when data is received. |
Copper link on / Receive activity (LKC) | This green LED is operational only when power is applied. The LED is on when the 100Base-TX link is on and flashes with a 50% duty cycle when data is received. |
Switches - accessible through a side opening in the chassis | |
Auto-Negotiation (802.3u) | Enabled (Default) - The media converter uses 802.3u Auto-negotiation on the 100Base-TX interface. It is set to advertise full duplex.
Disabled - The media converter sets the 100Base-TX port to full duplex. |
Pause | Pause should be enabled when all devices connected to the media converter support pause. Auto-Negotiation must be Enabled to use this feature.
Enabled (Default) - The Media converter will advertise Pause capability during Auto-Negotiation on the 100Base-TX interface. Disabled - The Media converter will advertise that it does not have Pause capability during Auto-Negotiation on the 100Base-TX interface. |
Link Pass Through | Enabled (Default) - When the state of the receiver is changed on the 100Base-TX interface it is reflected on the 100Base-FX fiber transmitter. When the state of the receiver on the 100Base-FX interface is changed it is reflected on the 100Base-TX transmitter.
When a Far-End Fault Indication is received on the fiber interface the 100Base-TX transmitter is turned off. When the Far-End Fault Indication is cleared the transmitter is turned back on. Disabled - The 100Base-TX and the 100Base-FX fiber interface operate independently. Far-End Fault indication on the 100Base-FX fiber interface has no effect on the 100Base-TX interface. |
Far-End Fault (FEF) | Enabled (Default) - The media converter transmits the Far-End Fault Indication over the 100Base-FX fiber connection whenever a receive failure is detected on the 100Base-FX fiber connection. The media converter continuously monitors the100Base-X fiber connection and clears the Far-End Fault Indication condition when a valid signal is received.
Disabled - Far-End Fault Indications are not transmitted regardless of the condition of the receive signal on the 100Base-FX fiber connection. |
Remote Loopback | The media converter can perform a loopback on the 100Base-X fiber interface.
Disabled (Default - Up) Enabled - The 100Base-X receiver is looped to the 100Base-X transmitter. The 100Base-TX transmitter is taken off the interface. |
Auto-MDIX (Internal Strap) |
If Auto-Negotiation (802.3u) is enabled, the media converter uses the HP Auto-MDIX method for the 100Base-TX interface. If Auto-Negotiation (802.3u) is disabled the Media converter will use the RX Energy method on the 100Base-TX interface to set the port MDI or MDIX whichever is appropriate.
Enabled (Default) - Either a straight-through or crossover type cable can be used to connect the media converter to the device on the other end of the cable. Disabled - If the partner device on the other end of the cable does not have the Auto-MDIX feature a specific cable, either a straight-through or crossover will be required to ensure that the media convertor's transmitter and the partner devices transmitter are connected to the others receiver. The Media Convertor's 100Base-TX port is configured as MDI with this switch setting. |
Cables | |
100Base-TX | RJ45 connector, 2 pair CAT 5, EIA/TIA 568A/B or better cable |
Magnetic Isolation | 1.5kv |
Fiber Optic Cable | Multimode: 62.5 / 125, 50/125, 85/125, 100/140 micron Single Mode: 9/125 micron (ITu-T 625) |
Packet Transmission Characteristics | |
Bit Error Rate (BER) | <10 -12 |
Environmental Specifications | |
Operating Temperature | 0 C to 50 C (32 F to 122 F) |
Storage Temperature | minimum range of -25 C to 70 C (-13 F to 158 F) |
Operating Humidity | 5% to 90% non-condensing |
Storage Humidity | 5% to 95% non-condensing |
Operating Altitude | Up to 3,048 meters (10,000 feet) |
Heat Output ( BTU/HR ) |
6.8 |
MTBF (Hours)** | Without power adaptor: 595,000 With power adaptor: 333,000 |
Chassis | Metal with an IP20 ingress protection rating |
Mounting | |
Din Rail Kit | Optional |
Rack Mount Kit | Optional |
Product Weight and Dimensions | |
Weight | 0.3 kg, 0.66 lbs |
Dimensions | 120 x 80 x 26 mm, 4.7 x 3.1 x 1.0 inches |
Packaging | |
Shipping Weight | 0.55 kg, 1.2 lbs |
Shipping Dimensions | 170 x 280 x 70 mm, 6.7 x 10.2 x 2.8 inches |
Regulatory Approvals | |
Emissions | FCC Part 15 Class B*, EN55022 Class B* |
CISPR 22 Class B* CISPR 32:2015/EN 55032:2015 (Class A) CISPR 24:2010/EN 55024:2010 |
|
EN61000-3-2 | |
Immunity | EN55024 |
Electrical Safety | UL 60950-1 |
IEC 60950-1(ed 2); am1, am2 EN 60950-1:2006+A11:2009+A1:2010+A12:2011+A2:2013 |
|
CE | |
Laser Safety | EN 60825-1:2007 |
Fiber optic transmitters on this device meet Class 1 Laser safety requirements per IEC-60825 FDA/CDRH standards and comply with 21CFR1040.10 and 21CFR1040.11. | |
Environmental | Reach, RoHS and WEEE Compliant |
Other | ECCN: 5A991 |
HTSUS Number: 8517.62.0020 | |
Perle Limited Lifetime Warranty |
* When used with a Class B rated AC power adapter.
**Calculation model based on MIL-HDBK-217-FN2 @ 30 °C
Fast Ethernet da Switch UTP a Switch UTP |
---|
Aumento della distanza tra due switch collegati con cavi a coppie ritorte ![]() |
Fast Ethernet da Switch UTP a Switch in Fibra |
Connessione di uno switch UTP con uno Switch in Fibra ![]() |
Collegamento Diretto - Lunga Distanza |
Connessione diretta fra due dispositivi remoti ![]() |
Infrastruttura Aziendale |
Infrastruttura aziendale che utilizza fibre ottiche ![]() |
Monomodale / Fibra Singola |
Collegare le porte in rame mediante un cavo in fibra single strand (detto anche "Bi-Direzionale" o BiDi) ![]()
Tuttavia, per contenere i costi, o se la fibra disponibile è limitata, è possibile utilizzare la tecnologia WDM. La tecnologia WDM impiega frequenze di trasmissione e ricezione separate per comunicare attraverso cavi in fibra single strand. Questa tecnologia sfrutta il fatto che la fibra ottica è in grado di trasmettere fasci di luce a diverse lunghezze d'onda simultaneamente, senza che queste interagiscano tra loro. In questo modo, una fibra singola è in grado di trasportare diversi segnali o canali su lunghezze d'onda differenti simultaneamente. Quindi, se si utilizzano cavi in fibra single strand, è necessario installare un media converter di tipo "Up" a un'estremità e un convertitore di media di tipo "Down" all'altra per garantire la conversione da rame a fibra. Perle offre un'ampia varietà di convertitori di media ("Up/Down") a fibra singola per il collegamento di 10BaseT, Fast Ethernet e Gigabit a cavi in fibra single strand. Sia che vi occorra una versione gestita o non gestita, standalone o con telaio modulare, da 20 o 120 km, Perle è in grado di offrirvi il modello più adatto a soddisfare le vostre esigenze di conversione in fibra. |
Select a Model to obtain a Part Number - Unmanaged Stand-alone Media Converters - Fast Ethernet to Fiber
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-100-M2ST2 | Dual ST |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-100-M2SC2 | Dual SC |
100Base-FX |
-20.0 |
-12.0 |
-31.0 |
-14.0 |
11.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-100-M2LC2 | Dual LC |
100Base-FX |
-20.0 |
-12.0 |
-30.0 |
-14.0 |
10.0* |
1310 |
MMF |
2 km (1.2 mi) |
S-100-S2ST20 | Dual ST |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-100-S2SC20 | Dual SC |
100Base-LX |
-18.0 |
-7.0 |
-32.0 |
-3.0 |
14.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-100-S2LC20 | Dual LC |
100Base-LX |
-15.0 |
0.0 |
-34.0 |
-5.0 |
19.0 |
1310 |
SMF |
20 km (12.4 mi) |
S-100-S2ST40 | Dual ST |
100Base-EX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1310 |
SMF |
40 km (25 mi) |
S-100-S2SC40 | Dual SC |
100Base-EX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1310 |
SMF |
40 km (25 mi) |
S-100-S2LC40 | Dual LC |
100Base-EX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1310 |
SMF |
40 km (25 mi) |
S-100-S2ST80 | Dual ST |
100Base-ZX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1550 |
SMF |
80 km (50 mi) |
S-100-S2SC80 | Dual SC |
100Base-ZX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1550 |
SMF |
80 km (50 mi) |
S-100-S2LC80 | Dual LC |
100Base-ZX |
-5.0 |
0.0 |
-34.0 |
-3.0 |
29.0 |
1550 |
SMF |
80 km (50 mi) |
S-100-S2ST120 | Dual ST |
100Base-ZX |
0.0 |
5.0 |
-35.0 |
-3.0 |
35.0 |
1550 |
SMF |
120 km (75 mi) |
S-100-S2SC120 | Dual SC |
100Base-ZX |
0.0 |
5.0 |
-35.0 |
-3.0 |
35.0 |
1550 |
SMF |
120 km (75 mi) |
S-100-S2LC120 | Dual LC |
100Base-ZX |
0.0 |
5.0 |
-34.0 |
-3.0 |
34.0 |
1550 |
SMF |
120 km (75 mi) |
Single Fiber Models Recommended use in pairs
Model | Connector |
Type |
Transmit (dBm) |
Receive (dBm) |
Power Budget (dBm) |
Wavelength (nm) |
Fiber Type |
Operating Distance |
||
---|---|---|---|---|---|---|---|---|---|---|
Min |
Max |
Min |
Max |
|||||||
S-100-M1ST2U | Single ST |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km (1.2 mi) |
S-100-M1ST2D | Single ST |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km (1.2 mi) |
S-100-M1SC2U | Single SC |
100Base-BX-U |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1310 / 1550 |
MMF |
2 km (1.2 mi) |
S-100-M1SC2D | Single SC |
100Base-BX-D |
-15.0 |
0.0 |
-28.0 |
-8.0 |
13.0 |
1550 / 1310 |
MMF |
2 km (1.2 mi) |
S-100-S1ST20U | Single ST |
100Base-BX-U |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km (12.4 mi) |
S-100-S1ST20D | Single ST |
100Base-BX-D |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km (12.4 mi) |
S-100-S1SC20U | Single SC |
100Base-BX-U |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1310 / 1550 |
SMF |
20 km (12.4 mi) |
S-100-S1SC20D | Single SC |
100Base-BX-D |
-14.0 |
-8.0 |
-32.0 |
-3.0 |
18.0 |
1550 / 1310 |
SMF |
20 km (12.4 mi) |
S-100-S1SC40U | Single SC |
100Base-BX-U |
-8.0 |
-3.0 |
-33.0 |
-3.0 |
25.0 |
1310 / 1550 |
SMF |
40 km (25 mi) |
S-100-S1SC40D | Single SC |
100Base-BX-D |
-8.0 |
-3.0 |
-33.0 |
-3.0 |
25.0 |
1550 / 1310 |
SMF |
40 km (25 mi) |
The minimum fiber cable distance for all converters listed is 2 meters.
*Based on use with 62.5/125 micron multimode fiber.
Media Converter Accessories |
|
---|---|
4 DIN Rail Mount Bkt | DIN Rail Mounting Kit |
MCSM | Standalone media converter wall mount bracket |